New Build Started: 3 Inch Acrobrat HD Freestyle Quadcopter

Written by: Tony Korologos | Date: Friday, July 26th, 2019
Categories: Aerial ImageryBuild LogEquipmentFPVMultirotor Aircraft
Tags:

I just started up my 3rd build in three weeks.  This one is the three inch Acrobrat HD Freestyle Quadcopter.  I had “accidentally” bought some motors and decided to build a quad around them. Hehe.

This one will have a RunCam split camera. The Split is not only an FPV camera, but also captures 1080p/60fps HD.  That camera along with the Acrobrat frame which has some nice vibration dampening makes for a quad that can produce some fantastic HD video without a GoPro. We shall see.

This build is about half way done. Should be launching it this weekend.

 

 

 


2 Inch FPV Quadcopter Build

Written by: Tony Korologos | Date: Thursday, July 18th, 2019
Categories: Build LogDrones For GoodEquipmentFPVMultirotor Aircraft
Tags:

My last true build was back in 2015. After a long break from building, flying, and crashing, I’m back at it.  I’m going down the FPV racing road and having a blast flying FPV.  Having built a giant hexacopter in the past, I’m now building the exact opposite, a tiny tiny micro quadcopter with two inch props.

Frame

I found this iFlight iX2 frame on Amazon for $16.99.  It’s a 100mm frame built for two inch props and a micro FPV camera.

Electronics

  • Flight Controller: Lumenier MICRO LUX V2 – F4 Flight Controller + OSD
  • ESCs: Lumenier Mini BLHeli_S 12A 4-in-1 OPTO ESC DSHOT
  • Receiver: FrSky XM+ SBUS
  • Video Transmitter: AKK FX3 5.8GHz 25mW-600mW VTX with OSD
  • Motors: BeeMotor 1108 5000KV brushless motor
  • FPV Camera: RunCam Phoenix Oscar Edition 1000tvl 2.5mm lens
  • FPV Antenna: Lumenier Micro AXII SMA 5.8GHz Antenna (RHCP)

Assembly

I haven’t done much soldering over the last few years, so it was a little tough to start back up on this build.  The electronics are all 20×20 mounts.  They’re very, very small.  So soldering wires to the pads on the flight controller was challenging.

I got the entire electronics stacked in the middle, but I’m probably going to need to rotate the FC 90 degrees to make it easier to access the USB port for configuration.

During assembly, when I’ve got the bird powered, the RunCam gets quite hot.  Not sure that’s normal or not.

I’ve got the receiver bound to my transmitter and I can arm the props.  I’m waiting on proper sized/powered batteries to fly it.  I strapped a 3S 450 on it but it was waaaaay too big.  I tried to liftoff with it but instead the props flew off and landed on my neighbor’s roof!

Maiden Soon

I hope to do a true maiden flight in the next couple of days.  Stay tuned.

 

 


FPV Camera and Transmitter Installed on Arris X-Speed 250 Quadcopter

Written by: Tony Korologos | Date: Friday, August 14th, 2015
Categories: Build LogMultirotor Aircraft
Tags:

Speedy Quadzales ‪#drone‬ build update. Now have FPV (first person view) camera and transmitter installed. Also worked up a bug antenna style setup for the two receiver antennae. Testing tomorrow.  This racer is the Arris X-Speed 250.

DSC01567 DSC01582


  • Social

  • Tags

  • Recent Posts

  • Recent Comments

  • Meta

  • Archives